Cisco C9105AXW-S – Bộ phát Wifi

Part Number

C9105AXW-S

Software 

Catalyst 9105AXW
- Cisco Unified Wireless Network Software Release 8.10MR3 or later
- Cisco IOS® XE Software Release 17.3.1 or later

Supported wireless LAN controllers

- Cisco Catalyst 9800 Series Wireless Controllers
- Cisco 3504, 5520, and 8540 Wireless Controllers and Cisco Virtual Wireless Controller

802.11n version 2.0 (and related) capabilities

- 2x2 MIMO with two spatial streams
- Maximal Ratio Combining (MRC)
- 802.11n and 802.11a/g
- 20- and 40-MHz channels
- PHY data rates up to 444.4 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz)
- Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive)
- 802.11 Dynamic Frequency Selection (DFS)
- Cyclic Shift Diversity (CSD) support

802.11ac 

- 2x2 downlink MU-MIMO with two spatial streams
- MRC
- 802.11ac beamforming
- 20-, 40-, 80- MHz channels
- PHY data rates up to 866.7 Mbps (80 MHz with 5GHz)
- Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)
- 802.11 DFS
- CSD support
- WPA3 support

802.11ax 

- 2x2 uplink/downlink MU-MIMO with two spatial streams
- Uplink/downlink OFDMA
- TWT
- BSS coloring
- MRC
- 802.11ax beamforming
- 20-, 40-, 80- channels
- PHY data rates up to 1.488 Gbps (80 MHz with 5 GHz and 20 MHz with 2.4 GHz)
- Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)
- 802.11 DFS
- CSD support
- WPA3 support

Integrated antenna 

Catalyst 9105AXW
- 2.4 GHz: Peak gain 3 dBi, internal antenna
- 5 GHz: Peak gain 5 dBi, internal antenna

Interfaces 

Catalyst 9105AXW
- 1x 100/1000/2500 Base-T (Ethernet) Uplink Interface
- 3x 10/100/1000 Base-T (Ethernet) Downlink Interface (LAN1,LAN2 and LAN3, LAN1 supports 10.5W PSE Power Budget)
- Management console port (RJ-45)
- USB 2.0 at 4.5W
- Passthru Port

Indicators 

- Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors

Dimensions
(W x L x H)

- Access point (without mounting brackets):
◦ C9105AXW: 3.54 x 6.3 x 1.3 in. (90 x 160 x 32.66 mm)

Weight 

Cisco Catalyst 9105AXW
- 0.8 lb. (373.2g)

Input power requirements

- 802.3at Power over Ethernet Plus (PoE+), Cisco Universal PoE (Cisco UPOE®)
- Cisco power injector, AIR-PWRINJ6=
- 802.3af PoE
- Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af)

Environmental 

Cisco Catalyst 9105AXW
- Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)
- Nonoperating (storage) altitude test: 25˚C, 15,000 ft (4600 m)
- Operating temperature: 32° to 122°F (0° to 50°C)
- Operating humidity: 10% to 90% (noncondensing)
- Operating altitude test: 40˚C, 9843 ft (3000 m)
Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 2x2 to 1x1 on the 2.4 GHz radio and the USB interface and LAN1 PSE will be disabled.

Available transmit power settings (Max/Min)

- 2.4 GHz
◦ 20 dBm (100 mW)
◦ -7 dBm (0.2 mW)

- 5 GHz
◦ 20 dBm (100 mW)
◦ -7 dBm (0.2 mW)